Our facilities have been producing a brand new line of chandeliers and sconces based off historic and old-fashioned lighting fixtures. Do take note as these are not the normal recreations that has made a name for our company so far, these are new designs building upon past techniques to make works of art that are uncomparable to other hardware of it's kind. Look to the photo below for a good example. This is our Edgar Brandt imspired Art Deco chandelier, extrapilated from the ideas Edgar Brant put into use when he first began creating chandeliers that would one day be known as Art Deco.

This impressive and stunning chandelier is a part of our newer series that we began putting out into the market just a few years ago. The addition of these new works allows us to customize them in a way that hasn't been done before with chandeliers of this kind. In particular, the hang length and the type of glass in the bottom itself can be adjusted to suit specific needs in lighting. We've been creating original spins on old style lighting while maintaining the rustic metalworked style of Art Deco, and this isn't the only set we've been able to do this with. Shown below is the Soleure series large 14 light chandelier that speaks volumes about our ability to modernize and adapt older pieces. In particular, this specific fixture has been remodeled to fit E-26 as well as LED bulbs which is highly uncommon for works simmilar to it. Beneath it are the matching sconces, which help to set a specific tone or flair of a room.

With the addition of chandeliers and sconces designed and produced in our shop, one feature we can give to customers is extra customizabliity. Works like these can't be found because we as a company are the ones designing them. In this case, the hang length as well as the type of glass in the bottom itself can be adjusted to suit specific needs in lighting. We have taken an extreme amount of detail in order to craft chandeliers that are new, but still retain the same feel as if they were made by the original artist himself. These are just a small sample of many in our newer line that hasn't been showcased enough.

An outstanding exterior/interior commercial building sconce.  No expense was spared with the KENK design to make this sconce a breath taking lighting device.

Made from solid brass/bronze material, it weighs in at over 100 lbs of solid brass.  It is completely cast by the lost wax casting method (also used to make the finest jewelry) and is a true labor of skilled casting to accomplish the lovely reticulated panels and design.

Not only is this light fixture simply gorgeous and impressive, but it is highly energy efficient.

It is California approved for new and restoration construction with the complete LED lighting system and our UL rating.  It is approved for dry, damp and wet locations.  Our patent pending barrel design LED tube array uses standard T-8 fittings with our three foot LED SMD tubes (stock number 36-D-55) which can be used dimmable, if so desired.  If not desired, it lights at 100% lumen value.  Even the small LED SMD bulb, in the bottom section, is housed in an energy approved GU10 socket.  It only lights the small bottom section and it is also dimmable.

Wattage:::::

The barrel inside the light contains six 12 watt LED SMD tubes giving a total of 72 watts.  The small GU10 bulb is 9 watts which gives the fixture a 81 watt total energy consumption.  It produces approximately 9,000 lumens.  This would be roughly equivalent to 900 watts of incandescent lighting.  While this sounds like a fantastic amount of light, please note that the light must come thru the opalescent acrylic shade which reduces the light to a pleasant appearance.

The acrylic shade is ONE piece from the top section, thru the center section and stops before the bottom section.  The electrical supply comes thru the acrylic shade via a waterproof pvc cord connector via SVT waterproof wire.  A length of SVT is left loose, inside the body of the light, so the entire center light column can be dropped-down when maintenance is required.

Maintenance is accomplished by:::::

The very top finial of the light is actually a functional part.  It is “O” ring installed disguised functional nut.  Once this finial is un-screwed, the light column can be lowered thru the bottom section for maintenance.  To allow the column to drop-down, the bottom section of the light is removed with three screws for access.

Supplies::::

We recommend using Lutron CL LED dimmers, which we keep on hand.  Naturally, we stock both replacement tubes (stock number 36-D-55) and GU10 dimmable bulbs for this fixture.

Measurements:::::

Maximum measurement wide is 16 1/2”.  Projection from the wall is 18”.  Overall height from top of the finial to the bottom finial is 50 1/2”.

Installation:::::

The heavy cast bronze backplate has four mounting holes.  We will supply four lag bolts, with decorative theft prevention brass heads for the installation of this fixture.  The lags are 3/8” diameter (9mm) and 2 1/4” long (55mm).  The heads of the lag bolts are drilled and tapped to receive the smooth brass heads AFTER installation.  Using locktite 272 on those decor heads will help to prevent any vandal or theft attempts.  Expansion wall anchors, for our lag bolts, is the contractors decision are not supplied by us due to the range of mounting surfaces.

Includes all six LED SMD tubes and bottom LED SMD bulb.  Ready to hang.